Keynote Lectures
Part and Material Properties in Selective Laser Melting of Metals
Advancements in Fundamental Studies on EDM Gap Phenomena

Electrical Discharge Machining （EDM）
Onthe Characterization of the Heat Input for Thermal Modelling of the EDM Process
Optimization of EDM Parameters on Nonconductive Ceramics Using Grey Relational Analysis
Time Estimation for Sinking EDM Operations
Study of High Efficient Discharge Cutting Solar Silicon and Texturing Directly
Influence of Additives in Dielectric Fluids for Electrical Discharge Machining
Performance Characteristics of Dry EDM
EDM Characteristics of Carbon Fiber Reinforced Plastic
Research of the Rosin in Machining Fluid for Electrical Discharge Machining
The Methodology of Detecting Dynamical Properties of Electrical Discharge Machining （EDM） Process towards Building
a Timely Varied Linear Predictive Model
Powder Mixed Near Dry Electrical Discharge Machining
Experimental Study on Single-pulse Discharge in Gas Dielectric
A New Discharge State Recognition Method of EDM Based on Pulse Edge Detection
Simultaneous Electrical Discharge Machining of Rectilinear Holes Using Electrodes of Various Diameters
Modeling of Workpiece Removal Rate on EDM
Mist-jetting Electrical Discharge Truing and Dressing Technology Combined with Mechanical Method on Metal-bonded
Diamond Grinding Wheel
Electrical Discharqe Truinq for Micro Electroplated Diamond Tool
About the Static Gap Pressure in Electro Discharge Drilling Process
Observation of Flying Debris Scattered from Discharge Point in EDM Process
Verification of Basic Performance of Size-Reduced Automatic Discharge Gap Controller for Curved Hole Electrical
Discharqe Machininq
Electrical Discharge Machining Properties of Insulating Si3N4 Ceramics with Added Al2O3
Effects of Process Parameters on Single Discharge Forces
Investigation on Dynamic Gas Bubble Formation by Using a High-Speed-Camera System
Study of Gap States in Bunched-electrode EDM
Numerical Simulation of Uneven Wear of Shaped Electrode in EDM
Surface Modification Using Electrical Discharge in Air Gap
Advanced Strategies for Improving the Surface Integrity in Electroerosion Machining
Characteristics of Electrical Discharoe Machinina for Maanetic Material
Effective Pulses Discriminator and Direct-Drive Jump Control for High Efficiency Electrical Discharge Machining （EDM）
Processes
Response Surface Methodology Approach to Process Modeling and Optimization of Powder Mixed Electrical Discharge
Machining （PMEDM）
The Study and Application of Pulse Generator in EDM Mirror Machining
Advancement in High Speed Electro-Erosion Processes for Machining Tough Metals
Experiment Research of the Electrical Discharge Machining Parameters Effected on Microstructure of Polycrystalline
Diamond
Research on EDM Mechanism of Polycrystalline Diamond
High-Speed Electroerosion Milling of Superalloys
Monitoring of EDM Gap Discharge Status with Wavelet Transform Method
Investigations on High Speed Electroerosion Machining of Forged Carbon Steel

Wire Electrical Discharge Machining （WEDM）
Measurement of Wire Deflection in Wire-cut EDM Machining
Mechanism of High Efficient Discharged Cutting on Low Doped Silicon
Development of On-the-Machine Surface Modification Technology in WEDM
A New Additive and Application System for Wire-EDM
Wire EDM of WC- ZrO2 Composites
Influence of Needle Pulse Shifting on the Basis Pulse for Wire-EDM of Hard Metals
On-line Estimation of Workpiece Height in WEDM
Trajectory Planning for the Four Axis WEDM Machine Tool and Its Implementation
Parameter Optimization for Surface Roughness of Multiple Cut on HS-WEDM Based on Genetic Algorithm
Monitoring Technology of Gap Discharge Status Based on Floating Threshold for WEDM
A Novel Discharging Status Distinguish Method on Machining Si3N4 by HS-WEDM
Investigations on the Influence of Powder Suspended Dielectrics in Wire-EDM
WEDM of Aerospace Alloys Using　Clean Cut Generator Technology

Electrochemical Machining （ECM， Electro forming）
Experimental Study of Hydrodynamic Bearing Groove Machining Using Fixed Position Cathode Pulse ECM
Selected Problems of Pulse Electrochemical Machining
Fundamental Research on Electrochemical Micro-machining by Using Water as the Electrolyte
Preparation and Analysis of Two-dimensional Nickel Dendrite with Fractal Structure
Research on Electrochemical Dissolution Localization in Case of Micro Machining with Ultra Short Pulses
Material Structure Influence on Surface Roughness in Nanofinishing Electrochemical Process
Research on Porous Metal Nickel in Jet Electrodeposits
Research on Micro Electrode Fabrication Based on ECM
Research on Micro ECM Using Micro Array Electrode
Aspects of Improving of Electrochemical Machining Accuracy
Study on Electrolyte Jet Turning
Mechanism and Process Study of Ultrasonical Vibration Combined Synchronizing Pulse Electrochemical Micro-Machining
Development of Gap-width Controlling System for Micro-ECM
Surface Improvement and Status Simulation of Alloy Tool Steel by Electrochemical Polishing
Experimental Study on Numerical Control Electrochemical Machining with BaU-end Tool-electrode
Design and Optimization of Process Parameters in Electrochemical Machining of Inconel 625 Alloy Using Taguchi Method
Research on NC Electrochemical Mechanical Machining Carbide Alloy
Micro Electrochemical Machining and Its Influencing Factors
Process Control and Power Systems for Electrochemical-Erosion Sinking （ELESIN）
Electrochemical Machining of Micro-profile on Copper

Ultrasonic Machining （USM）
Effect of Feed Velocity on Cutting Characteristics of Polycarbonate Sheet Subjected to a Two-line Wedge Indentation
Experimental Study on Ultrasonic Face Machining of Glass
Investigation of Micro Hole Drilling in Bovine Rib Using Micro Rotary Ultrasonic Machining

Laser Beam Machining （LBM）
Energy Attenuation Modelling for Laser Cladding Process with Coaxial Powder Nozzles
Fundamental Study on High-quality Dicing Method for Semiconductor Package by Fiber Laser
Fundamental Study on Micro-welding of Thin Stainless Steel Sheet by Fiber Laser
Erosion Behavior of Plasma-sprayed and Laser-remelted Ceramic Coatings on TiAI Intermetallic Surface
Research on Laser Micromachining at Medical Stents Manufacturing
Other High-Density Beam Machining （EBM， IBM， Plasma Processing）
Surface Finishing of Cemented Carbide by Large-area EB Irradiation

Abrasive/Water Jet Machining （A/WJM）
Unconventional Methods of Cutting of Bone and Tissue
Other Non-Traditional Machining Methods （Direct writing， PVM）
Optimization of Machining Parameters of a Novel Friction Drilling Process
Efficiency Improvement of Electrochemical Discharge Machining by a Magnetic Field-assisted Approach
Factor Influencing the Gas Film Performance of Electrochemical Discharge Machining
Hybrid Processes
Intelligent Control of Ultrasonic Vibration Assisted Grinding Combined with EDM
Optimization of Electrochemical Discharge Machining Process
Investigation on Ultrasound-assisted Electro-spark Deposition Processing
A Novel Hybrid Process for Fabricating the Micro Holes Array
A Hybrid Process of Micro EDM and Micro ECM for 3D Micro Structures
Passivating Film at the Electrochemical Discharge Drilling
Electro-discharoe Grindina， Enerav Consumption and Internal Stresses in the Surface Laver
Hybrid EDM： Ultrasonic Vibration Assisted EDM Applied to Micro-Holes
……
Rapid Manufecturing
Micro and Nano Machining by Nontraditiona Methods
Process Modeling and Simulation
Author Index